Emergency Light 3W Fire Exit Sign Board

EYJD-01

New product

Emergency Exit Light 3W Fire Exit Sign AC220V~AC240V 50/60Hz 3 Years Warranty

More details

By buying this product you can collect up to 19 loyalty points. Your cart will total 19 loyalty points that can be converted into a voucher of 95.00 ฿.


1,940.00 ฿

Free Google QRcode module from Mediacom87

Add to wishlist

More info

Emergency Exit Light 3W Fire Exit Sign AC220V~AC240V 50/60Hz 3 Years Warranty

  • Sound and light alarming function
  • Overcharge protection
  • LED charging indicator
  • Automatical Power switch

Caution: 

  • keep power supply within nomaial range (AC220V~240V 50 / 60Hz)
  • Installation must be away from hyperthermia substance,gas or exhaust pipe
  • Prevent to fierce vibration or collision
  • Avert violent impregant or chemical usage while cleansing
  • Intelligence charging function
  • Rigorous design for short-unicircuit protection

Installation and inspection 

  1. Fix the device firmly on the ground by contrivance requirement.
  2. Wiring accurately refers to the connection diagram.
  3. Being inputted AC, the device runs primary power status, pressing the trial button to test whether or not emergency module is operated. While released the trial button, the device resumes general status.

Method of battery replacement 

  1. Cut the AC off, remove the plastic baffle from lateral of the steel case.
  2. Pull out the PCB circuit board gently
  3. Extract battery plug from both side
  4. Reverse the order above to assemble the device

Note:

  1. Please replace the battery on the proper direction. Reversal assembling might cause PCB damage.
  2. Please dispose the worn-out battery properly without contamination.

If the duration of the light can?t reach 30 minutes, the battery should be changed

Method of illuminant replacement 

  1. Cut the AC off, remove the plastic baffle from lateral of the steel case.
  2. Pull out the PCB circuit board gently
  3. Extract LED illuminant plug from PCB board
  4. Replace the same model illuminant
  5. Reverse the order above to assemble the device

Method of wiring: read the wiring diagram for detail information.

Inspection

Any issues induce the device malfunction, please take the inspection method below.

PHENOMENON

CAUSE

MEASURE

Red LED is off

1.Power supply failure

2.Improper power plug insert

3.PCB damage

1.Consult the electrician

2.Insert the plug properly

3.Remit the device for further inspection

Yellow LED is on

1.Battery failure

2.PCB damage

1.Check the battery plug

2.Remit the device for further inspection

Emergency period insufficiency

1.Insufficient charge

2.Prolonged inoccupation

1.Extend charge for 20 hours

2.Reiterate charge/discharge

3.If the duration of the product can?t reach 30 minutes, the battery should be changed.

Maintenance

  1. The device adopts evacuated Ni-Cd battery pack, please charge for 20 hours before application. The initial duration might be insufficient by prolonged inoccupation, please charge/discharge for 3 times thoroughly (charge for 20 hours and discharge until the battery empty), then the battery would be recovered.
  2. Barely use the identical fuse for substitution. For personnel safety please cut off the AC before replacement.
  3. Prolonged inoccupation might affect the battery life-span, we suggest charge/discharge every 3 months minimum. Charge/discharge every 6 months in general application.
  4. In general, the battery pack is able to charge/discharge for 500 times.
  5. Please grounding the device according to the grounding sign while application

Reviews

No customer reviews for the moment.

Write a review

Emergency Light 3W Fire Exit Sign Board

Emergency Light 3W Fire Exit Sign Board

Emergency Exit Light 3W Fire Exit Sign AC220V~AC240V 50/60Hz 3 Years Warranty

16 other products in the same category:

Viewed products