Electrostatic spraying machine PC03-5 small spraying equipment portable 5 gear adjustable spray machine 110/220V 1PC...
Warning: Last items in stock!
By buying this product you can collect up to 73 loyalty points. Your cart will total 73 loyalty points that can be converted into a voucher of 365.00 ฿.
Electrostatic spraying machine PC03-5 small spraying equipment portable
5 gear adjustable spray machine 110/220V 1PC
Note: Our default shipping color is black.
The product is the ideal spray tool for the appearance of various metal parts to make the
workpiece beautiful and durable. It can be sprayed for any metal parts, after forming the spray
surface to prevent a variety of chemical corrosion and ultraviolet radiation, much stronger than
the liquid spray, more than ten times more than ordinary paint. In the production process,
without adding any organic solvents, do not produce toxic volatiles, does not cause
Use this product without special training, as long as carefully read the instructions, you can
make a very short time to fully grasp, and skilled operation, to achieve your idea, access to
the ideal appearance of decorative pieces.
Power Requirements: Use a 220V AC power supply with a safety ground. When used, the
machine must be grounded.
Air supply requirements: the use of compressed air pressure must be 0.5 to 1.2 kg. It is
recommended to use 1.0 kg, this time the air pressure is the most ideal.
Environmental requirements: well ventilated, dry.
1. Because of the machine to produce high-voltage static electricity, the user in use, the
workplace, equipment must be dry. In addition the machine must be safely grounded, do not
pull out the grounding plug, which for the protection of the machine and to prevent electric
shock is very important. To avoid danger, after each use, the discharge needle should be
touched on the grounding clip discharge.
2. Plastic powder particles fall into the air, hit the fire, there is the risk of burning, explosion, it
must exclude all hidden dangers, and all the fire source isolation. Do not use a plastic cleaner
on the ground to clean up. Work to wear dust cover, to protect personal safety.
Two. Prepare work before use:
1. Spray the preparation of parts: the surface of the parts should be sprayed to the rust, to oil,
phosphating treatment, parts should have a dry, smooth, clean surface.
2. Prepare the oven one to put the sprayed parts into the oven. Sprayed parts are best hung
with metal spreader in the oven.
3. Prepare the same power and sockets as the sprayer's voltage. The power supply must be
4. Prepare the air supply. Air supply pressure is generally 0.5 kg to 1.2 kg, it is recommended
to use 1.0 kg air pressure.
5. The dry plastic powder into the bottle, the amount of plastic powder about 5 cm from the
bottom of the height is more appropriate.
Three. Common troubleshooting:
1. Spray surface powder layer is too thick, the formation of accumulation, after baking will make
plastic surface grain phenomenon. The accumulation of plastic powder can be used to blow the air.
2. Polyester powder after drying will cause the plastic surface to produce granular phenomenon,
so to control the surface powder layer thickness. For the resulting granular plastic surface, can
be used to polish the sandpaper with 400 grain size and then re-spray.
3. Spray the surface is not smooth or have pores, is caused by the humidity, the need to replace
the dry plastic powder or water vapor separator.
4. If the gun does not spray powder, may be too low air pressure, or water vapor separator too
much moisture, resulting in air intake, need to replace the water vapor separator.
5. Spray the plastic powder when the direction of dispersion can adjust the discharge end of the
dispenser and the distance between the gun body.
6. If the parts are found to be sprayed on the surface is not ideal, need to re-spray, you can use
parts with 400 grain sandpaper sand after re-uniform spray and then into the oven baking.
7. If you find the powder does not produce high-voltage static electricity, you should have a
professional knowledge of electrical engineers to check and repair, not to do anything to avoid
Scope: a variety of metal parts for the appearance of spray
Maximum output pressure: 25N / S
Power form: electric air spray machine
Spray width: 1 square
Pressure ratio: 6--8
Best Spray Distance: 0.5m
Note: If your area is a remote area, you will need to add a separate fee.
Notice : when the parcel arrived to your customs,please pay the tax and pick up the parcel,
we are not responsible for any customs duty or import tax
No customer reviews for the moment.
Electrostatic spraying machine PC03-5...