หน่วยแสดงผลแบบ Head Up OBD II 5.5 นิ้ว

OBD II Head Up Display Unit

Description:
With the head-up display driver can now see speed directly on the windshields, allows a driver to keep their head up (observing the road) and still see important vehicle information such as the car's Speed (mph/km), Rpm, Water temp, Volt on to your windshields Water temp , volt warning function which can be set up by user ( water temp gauge & volt gauge) Auto dim when dark Project Speed (mph/km), Rpm, Water temp, Volt on to your windshields Speed warning function which can be set up by user

Main Features:

• Plug and play. Activesafety HUD can auto adapt to vehicle type which in line with OBDII or EUOBD(On-Board Diagnostic System).
• Comprehensive display. Activesafety HUD can display many parameters at the same time as follows, vehicle speed, engine speed, water tempe- rature (voltage, throttle valve position, ignition advance angle, time of 100 km acceleration),fuel consumption, mileage, low fuel tips, engine failure.
• Diversiform display mode. Driver can chose normal display mode, high- speed display mode and automatic display mode.
• Free switch. Km and mile can be switched freely to meet the need of inch auto meter.
• Suitable size. The display area is 5.5 inches which is very clear for driver to read data.
• Automatic power on and off. Starting with the vehicle starting, stopping with the vehicle stopping to protect the vehicle’s battery. Moreover, we pre- serve the hand switch function to control the HUD.
• Flexible alarm mode. Activesafety HUD can offer single-stage and four-stage overspeed alarm modes to choose to make driving safer.
• Engine speed alarm. It contributes to shift gear in time to save fuel also has significance to new driver.
• Flexible brightness adjustment. The brightness can be adjusted automatically or manually to reach the best state which is in harmony with the environment.

Function Instructions:

1. Parameter value: show the value with the units of kilometers, miles and engine speed.
2. OBDII port: connect the car and HUD.
3. Fuel icon: flash when the fuel is not enough to drive 100km.
4. Engine failure: flash when vehicle’s engine has problems.
5. Engine speed: show the state of engine speed.
6. Engine speed icon: indicate the parameter value of engine with units of 1000r. It will flash when engine speed is alarming.
7. Speed alarm: flash when speed exceeds the preset values.
8. Rest tips: flash when drive continuously for more than 4 hours with HUD starting.
9. Sound switch: light when voice alarm is opened.
10. Fuel consumption icon: show fuel consumption is calculating.
11. Fuel parameter value: show the consumption of fuel in recent driving.
12. Dial button: multi-function switch, you can dial to left or right, you can enter into setting mode by long press. And also has the ability to decrease or increase fuel.
13. Fuel consumption per hour: show oil mass consumption per hour in driving.
14. Light sensor: sense the external light intensity and adjust the HUD’s brightness to adapt to environment automatically.
15. Fuel consumption per 100km: show the fuel consumption per 100km in driving.
16. Voltage, throttle valve, water temperature, ignition advance angle and acceleration per 100km: voltage shows the vehicle’s voltage; throttle valve shows the size of itself; water temperature shows the temperature of vehicle cooling fluid; ignition advance angle shows the angle of twist in firing, it’s also a mark of engine’s efficiency. Acceleration per 100km shows performance of the vehicle’s acceleration per 100km.
17. Seconds: show the unit of acceleration per 100km.
18. Parameter value: show parameter value of Voltage, throttle valve, water temperature, ignition advance angle and acceleration per 100km.
19. Mileage: light when the fuel only sustains 100km.
20. Reel per minute: show the unit of engine speed if you multiply the parameter value with 10.
21. Kilometer per hour: show the unit of speed.
22. Mile per hour: show the unit of speed.

Notice: Applicable OBD II Generations after 2003 Interface

Main Technical Indicators:

1. Service conditions:
   1. Environment temperature: -400C—+800C
   2. Barometric press: 86—106 KPa
   3. Relative humidity: 10%—95%
   4. Environment voice: <=60 dB(A)
2. Alarm of sound level:> =30dB(A)
3. Work voltage: 9V~16Vdc(12Vdc/400mA)
4. Size of product: 14x85x147 (mm)
5. Weight of product: 320g

Packing list:
1 x English Manual
1 x Cable
1 x Protective film
1 x Mats